ChinaAutoRegs｜GB 18352.5-2013英文版/English/翻译/轻型汽车污染物排放限值及测量方法（中国第五阶段）-国五排放标准
Limits and measurement methods for emissions from light-duty vehicles (CHINA 5)
1 SCOPE
This Standard specifies the limits and measurement methods for emission pollutants at normal and low ambient temperature, emission pollutants at two-speed idle condition, crankcase emissions and evaporative emissions, and technical requirements and measurement methods for the durability of pollution control devices and on-board diagnostic (OBD) systems of light duty vehicles equipped with positive-ignition engines.
This Standard specifies the limits and measurement methods for emission pollutants at normal ambient temperature and free acceleration smoke, and technical requirements and measurement methods for the durability of pollution control devices and on-board diagnostic (OBD) systems of light duty vehicles equipped with compression-ignition engines.
This Standard specifies the requirements for type-approval of light duty vehicles, check and verification methods of conformity of production and In-service conformity.
This Standard also specifies the special requirements for vehicles fuelled by LPG or NG.
This Standard also specifies the type-approval procedure for replacement pollution control devices as separate technical units intended to be fitted on light duty vehicles with respect to pollutant emissions.
This Standard also stipulates the technical requirements for vehicles that use a reagent for the exhaust after-treatment system and the procedure for emission test of vehicles equipped with periodically regenerating systems.
This Standard applies to vehicles, including hybrid electric vehicles, powered by positive-ignition engines or compression-ignition engines, with the maximum design speed of being greater than or equal to 50 km/h.
At the manufacturer’s request, type approval may be performed for Category M1, M2 and N2 vehicles with the maximum mass not exceeding 3,500 kg and a reference mass not exceeding 2,610 kg in accordance with this standard; as for the vehicles type approval granted under this standard may be extended from vehicles mentioned above to M1, M2, N1 and N2 vehicles with a reference mass not exceeding 2,840 kg and which meet the conditions laid down in this standard.
This Standard not applies to the vehicles that its type had been approved in accordance with GB 17691-2005 (China Stage V).
2 NORMATIVE REFERENCES
The following normative documents or contain provision which, through reference in this text, constitute provisions of this national standard. For all undated references, the valid edition of the normative document referred to applies.
GB 1495 Limits and measurement methods for noise emitted by accelerating motor vehicles
GB 3847-2005 Limits and measurement methods for exhaust smoke from C.I.E. (Compression Ignition Engine) and vehicle equipped with C.I.E.
GB 7258 Safety specifications for power-driven vehicles operating on roads
GB/T 15089-2001 Classification of power-driven vehicles and trailers
GB 17691-2005 Limits and measurement methods for exhaust pollutants from compression ignition and gas fuelled positive ignition engines of vehicles (III, IV, V)
GB 18285 Limits and measurement methods for exhaust pollutants from vehicles equipped ignition engine under two-speed idle conditions and simple driving mode conditions
GB/T 19001-2008 Quality management systems – Requirements
GB/T 19755 Measurement methods for emissions from light-duty hybrid electric vehicles
HJ/T 390 Technical Requirement for Environmental Protection Product – Control System of Fuel Evaporative Pollutants from Vehicle WITH Petrol Engine
HJ 509 Determination of Platinum, Palladium and Rhodium loading in the vehicle-used ceramic catalytic converters Inductive Coupled Plasma-Optical Emission Spectrometry and Inductive Coupled Plasma-Mass Spectrometry
ISO 2575-1982 Road vehicles — Symbols for controls, indicators and tell-tales
ISO 8422-1991 Sequential sampling plans for inspection by attributes
ISO 9141-2 Road vehicles — Diagnostic systems — Part 2: CARB requirements for interchange of digital information
ISO 14230-4 Road vehicles — Diagnostic systems — Keyword Protocol 2000 — Part 4: Requirements for emission-related systems
ISO 15031-3 Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics – Part 3: Diagnostic connector and related electrical circuits, specification and use
ISO 15031-4 Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 4: External test equipment
ISO 15031-5 Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 5: Emissions-related diagnostic services
ISO 15031-6 Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 6: Diagnostic trouble code definitions
ISO 15031-7 Road vehicles — Communication between vehicle and external equipment for emissions-related diagnostics — Part 7: Data link security
ISO 15765-4 Road vehicles — Diagnostics on Controller Area Network (CAN) — Part 4: Requirements for emissions-related systems
EN 1822 High efficiency air filters (EPA, HEPA and ULPA)
SAE J1850 Class B data communications network interface
SAE J2186 E/E data link security
3 TERMS AND DEFINITIONS
For the purpose of this standard, the following terms and definitions apply.
3.1
Light-duty vehicle
Means the category M1, M2 and N1 vehicles with the maximum mass of not exceeding 3,500 kg.
***********************************************
现成译文，到款即发。
支持样页验证质量。免费提供增值税发票。
请联系 QQ: 564965870/微信: 13306496964/Email: standardtrans@foxmail.com 购买完整译文(PDF/Word)。
专业源于专注|ChinaAutoRegs 始终专注于机动车标准翻译！迄今为止已翻译上千个国内外汽车法规标准！独家打造千万级汽车专业术语库和记忆库。