ChinaAutoRegs｜GB/T 1040.2-2006 英文版/English/翻译/塑料 拉伸性能的测定 第2部分：模塑和挤塑塑料的试验条件
Plastics – Determination of tensile properties – Part 2: Test conditions for moulding and extrusion plastics

1 SCOPE

1.1 This part of GB/T 1040 specifies the test conditions for determining the tensile properties of moulding and extrusion plastics, based upon the general principles given in the Part 1.
1.2 This part is applicable to the following range of materials:
 rigid and semi-rigid thermoplastics moulding, extrusion and cast materials, including compounds filled and reinforced by e.g. short fibers, small rods, plates or granules but excluding textile fibers, in addition to unfilled types;
 rigid and semi-rigid thermosetting moulding and cast materials, including filled and reinforced compounds but excluding textile fibers as reinforcement;
 thermotropic liquid crystal polymers.
This part is not applicable to the materials reinforced by textile fibers, with rigid cellular materials or sandwich structures containing cellular material.
1.3 The specimens used in this part may be either moulded to the chosen dimensions or machined, cut or punched from injection- or compression-moulded plates. The multipurpose test specimen is preferred (see ISO 3167:1993, Plastics — Multipurpose test specimens).
Note: ISO 3167:1993 has been replaced by ISO 3167: 2002.

2 NORMATIVE REFERENCES

The following normative documents contain provision which, through reference in this text, constitute provisions of this part of GB/T 1040. For dated reference, subsequent amendments to, or revisions of, any of these publications (excluding corrigenda) do not apply. However, parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the Standards indicated below. For undated references, the latest edition of the normative document referred to applies.
GB/T 1040.1-2006 Plastics-Determination of tensile properties-Part 1: General principles (ISO 527-1:1993, IDT)
GB/T 17037.1-1997 Injection moulding of test specimens of thermoplastic materials-Part 1: General principles and moulding of multipurpose and bar test specimens (idt ISO 294-1:1996)
ISO 37:1974 Rubber, vulcanized – Determination of tensile stress-strain properties
ISO 293:1986 Plastics – Compression moulding test specimens of thermoplastic materials
ISO 295:1991 Plastics – Compression moulding of test specimens of thermosetting materials
ISO 2818:1994 Plastics – Preparation of test specimens by machining

1、现成译文，到款即发。
2、下单前可任取样页验证译文质量。
3、免费提供正规普通增值税数电发票。
4、请联系手机/微信: 13306496964/Email: standardtrans@foxmail.com 获取完整译文。
5、本英文译本为纯人工专业精翻版本，保证语法术语准确率和专业度！
6、专业源于专注|ChinaAutoRegs 始终专注于汽车标准翻译领域！
7、「中国汽车标准译文库」已收录上千个现行汽车国家标准和行业标准的英文版译本，涵盖传统燃油车、新能源汽车和摩托车标准化体系！独家打造千万级汽车专业术语库和记忆库。

1. The English Translation of this document (GB, GB/T, QC/T, CNCA, CQC, CAV, etc.) is readily available, and delivered immediately upon payment.
2. You may request for sample pages to your preference before placing an order.
3. Please contact standardtrans@foxmail.com for the complete PDF version in English.
4. Almost all of Chinese automotive/automobile standards, regulations and norms in effect have been included in our well-established database, providing one-stop, up-to-date, efficient and professional solution.