ChinaAutoRegs｜GB 20816-2006 英文版/English/翻译/车辆防盗报警系统 乘用车
Vehicle Security Alarm Systems – Passenger Cars
1 SCOPE
This standard specifies requirements and test methods for vehicle security alarm systems (hereinafter referred to as VSAS) intended for installation within vehicles used for the carriage of passengers and having not more than eight seats in addition to the driver’s seat.
The object of the standard is to ensure a high standard of safety, performance and reliability of VSAS and the reduction of false alarms.
This standard covers VSAS designed to detect and signal the unauthorized opening of any of the vehicle doors, boot/luggage compartment, bonnet/engine hood and, in addition, to immobilize the vehicle when set.
The standard covers VSAS intended both for installation as original equipment and for installation after delivery of the vehicle.
2 NORMATIVE REFERENCES
The following standards contain provisions which through reference in this text, constitute provisions of this Standard. For dated references, subsequent amendments (corrigenda excluded) to, or revisions of, any of these publications do not apply. However, parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions of the Standards indicated below. For undated references, the latest edition of the applicable Standards referred to apply.
GB 4208-1993 Degrees of protection provided by enclosure (IP code) (eqv IEC 529:1989)
GB14023 Vehicles, motor boats and spark-ignited engine-driven devices—Radio disturbance characteristics–Limits and methods of measurement(idt CISPR 12:1997)
ISO 512:1979 Road vehicles – Sound signaling devices – Technical specifications
ISO 7637-1:1990 Road vehicles – Electrical disturbances by conduction and coupling – Part 1: Passenger cars and light commercial vehicles with nominal 12 V supply voltage – Electrical transient conduction along supply lines only
ISO 7637-3:1995 Road vehicles – Electrical disturbances by conduction and coupling – Part 3: Passenger cars and light commercial vehicles with nominal 12 V supply voltage and commercial vehicles with 24 V supply voltage – Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines
ISO/TR 10605 Road vehicles – Electrical disturbances from electrostatic discharge
ISO 11451-1:1995 Road vehicles – Electrical disturbances by narrow band radiated electromagnetic energy – Vehicle Test methods – Part 1: General and definition
ISO 11451-2:1997 Electrical disturbances by narrow band radiated electromagnetic energy – Vehicle Test methods – Part 2: Off-vehicle radiation source
ISO 11451-3:1994 Electrical disturbances by narrow band radiated electromagnetic energy – Vehicle Test methods – Part 3: On-board transmitter simulation
ISO 11451-4:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Vehicle Test methods – Part 4: Bulk current injection (BCI)
ISO 11452-1:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Component test methods – Part 1: General and definition
ISO 11452-2:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Component test methods – Part 2: Absorber-lined chamber
ISO 11452-3:1996 Electrical disturbances by narrow band radiated electromagnetic energy – Component Test methods – Part 3: Transverse electromagnetic mode (TEM)cell
ISO 11452-4:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Component Test methods – Part 4: Bulk current injection (BCI)
ISO 11452-5:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Component Test methods – Part 5: Stripline
ISO 11452-6:1997 Electrical disturbances by narrow band radiated electromagnetic energy – Component Test methods – Part 6: Parallel plate antenna
ISO 11452-7:1995 Electrical disturbances by narrow band radiated electromagnetic energy – Component Test methods – Part 7: Direct radio frequency (RF) power injection
IEC 60068-2-11 Environmental testing – Part 2: Tests. Test Ka: Salt mist
IEC 60068-2-29 Basic Environmental Testing Procedures Part 2: Tests – Tests Eb and Guidance: Bump
IEC 60839-1-3:1988 Alarm systems – Part 1: General requirements – Section 3 – Environmental testing
1、现成译文，到款即发。
2、下单前可任取样页验证译文质量。
3、免费提供正规普通增值税数电发票。
4、请联系手机/微信: 13306496964/Email: standardtrans@foxmail.com 获取完整译文。
5、本英文译本为纯人工专业精翻版本，保证语法术语准确率和专业度！
6、专业源于专注|ChinaAutoRegs 始终专注于汽车标准翻译领域！
7、「中国汽车标准译文库」已收录上千个现行汽车国家标准和行业标准的英文版译本，涵盖传统燃油车、新能源汽车和摩托车标准化体系！独家打造千万级汽车专业术语库和记忆库。
1. The English Translation of this document is readily available, and delivered immediately upon payment.
2. You may request for sample pages to your preference before placing an order.
3. Please contact standardtrans@foxmail.com for the complete PDF version in English.
4. Almost all of Chinese automotive/automobile standards, regulations and norms (GB, GB/T, QC/T, CNCA, CQC, CAV, etc.) in effect have been included in our well-established database, providing one-stop, up-to-date, efficient and professional solution.